Ronan X11SN Instrukcja Użytkownika

Instructionsand Operating ManualSERIES X11SNWINDOW ANNUNCIATORSYSTEMS

system. The window display areas are con-tained within Ronan’s standard colored-bezels, allowing multiline engraving on sin-gle or sandwich lenses. Th

9.2 M, Manual Reset1. Acknowledge, reset and test push buttons.2. Alarm audible device.3. Lock-in momentary alarms until acknowledged.4. The audible d

PROCESSPROCESSPROCESSPROCESSPROCESSABNORMAL ORNORMALNORMALABNORMALABNORMAL ORNORMALABNORMAL ORNORMALFIRST OUTRESETFIRST ABNORMALRETURN TONORMALFIRST O

PROCESSPROCESSPROCESS PROCESSNORMALABNORMAL ORNORMALABNORMAL ORNORMALABNORMAL ORNORMALSUBSEQUENT TOABNORMALACKNOWLEDGEWHILE NORMALSUBSEQUENTALARMACKNO

10.1Monalarm Dimensional Drawings13A OverallA OverallB CutoutB Cutout2.75” (69.85 mm) High x3.00” (76.20 mm)WideAlarm WindowOptional Push-buttonFlashe

10.2Dualarm Dimensional Drawings19.00” (482.60 mm) OverallAOverall17.75” (450.85 mm) Rack Opening1.44” (35.56 mm) High x 3.00”(76.20 mm) Wide Alarm Wi

10.3 Trilarm Dimensional Drawings15A OverallA OverallB CutoutB Cutout.86” (69.85 mm) High x3.00” (76.20 mm)WideAlarm WindowOptional Push-buttonFlasher

10.4 Quadalarm Dimensional Drawings16A OverallA OverallB CutoutB Cutout1.44” (35.56 mm) High x1.44” (35.56 mm)WideAlarm WindowOptional Push-buttonFlas

1710.5 Standard Rear Terminal Arrangements and Wiring - 24 VdcMonalarm X11SN-1000Binalarm X11SN-2000Trialarm X11SN-3000Quadalarm X11SN-4000ABABAB123GC

1810.6 Rear Terminal Arrangements and Wiring for 125 Vdc Field ContactMonalarm X11SN-1000Binalarm X11SN-2000Trialarm X11SN-3000Quadalarm X11SN-4000AAB

TABLE OF CONTENTS1.0 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10.7 Rear Terminal Arrangements and Wiring for Transistor Input123GCAV-V+V+V+24 Vdc InputElectronicHornAC HornHorn 1 RelayAckSilenceTestResetHorn 2 Re

2010.8 Rear Terminal Arrangements and Wiring for Opto-coupled Input115 Vac, 24 Vdc, 48 Vdc, 125 VdcMonalarm X11SN-1000Binalarm X11SN-2000Trialarm X11S

X11SN FLASHERSWITCH/JUMPER OPTIONSDRAWING NUMBERX11C387REV021

RONAN ENGINEERING RONAN ENGINEERING RONAN ENGINEERINGCOMPANY LIMITED U.K. LIMITED .21200 Oxnard Street 1 Tilley Road 32 Bermondsey RoadWoodland Hills

1.0 GENERAL DESCRIPTIONThe Ronan Series X11SN Window AnnunciatorSystems feature Monalarm, Binalarm, Trialarm andQuadalarm displays within Ronan’s stan

5.0 MOUNTING A. The annunciator is shipped with all of the alarm/lamp modules, auxiliary contact module(s) andflasher module(s) installed in

6.0 POWER UP AND TESTPROCEDUREIt is important to review all external equipment,including the alarm system, before turning onpower and proceeding with

connected common for first alert sequencegroups. Now remove the alarm modules oneat a time and determine whether or not thenormally closed/normally op

67.3 Step-by-step ProceduresA. Check the system voltage and verify polar-ity of supply input voltage and that the sys-tem voltage lines are not ground

7These terminals are located in the rear, lower left corner of the chassis. There can only beone master flasher in any synchronized chain.All other sy

Bypass Switch SelectionChannel A(1) and Channel C(3) in ON position by-passes the time selected by TIME. The FC responsefor Channel A and Channel C wi